OpenWrt Chaos Calmer 15.05 正式发布

[lhbc]

** Highlights since Barrier Breaker **

• Linux kernel updated to version 3.18
• Improved Security Features
  • Rewritten package signing architecture based on ed25519
  • Added support for jails
  • Added support for hardened builds
• Improved Networking Support
  • Added or improved support for lots of 3G/4G modems (MBIM, QMI, NCM, ...)
  • Added support for 464XLAT (CLAT ) [RFC 6877 + RFC 7050]
  • Netfilter performance enhancements (conntrack route cache )
  • Improved support for self-managing networks [draft-ietf-homenet-hncp]
  • Better multi-core support for the network stack
  • Improved support for MAP-E, MAP-T and LW4over6 IPv4 transitioning technologies [draft-ietf-softwire-map, -map-t, -map-dhcp, -lw4over6]
  • Improved network auto-setup capable of detecting and bootstrapping IPv4-only, 6rd, Dual-Stack, IPv6-only, DS-Lite, LW4over6, MAP-E, MAP-T, 464XLAT and combinations without explicit configuration [based on RFC 7084]
  • Added support for Smart Queue Management (SQM ) QoS, AQM and Traffic Shaping
  • Improved support for DNSSEC
• Platform and Driver Support
  • Added support for feeds of externally maintained targets
  • New mt7621 subtarget for Mediatek 11ac SoC
  • New mt76 mac80211 based wifi driver for MTK 11ac cores.
  • New mwlwifi mac80211 based wifi driver for the Marvell 88W8864
  • New bcm53xx target for Broadcom ARM BCM47xx/53xx devices
  • New mxs target for Freescale i.MX23/28 family and various boards
  • New sunxi target for AllWinner A10/A13/A20 family and various boards
  • brcm2708: support for Raspberry Pi 2
  • brcm63xx: support for BCM6318 and BCM63268 family
  • brcm63xx: improved fallback sprom support with bcma support

https://openwrt.org

[ipv6nxtgnwrt]

已刷，正在研究 464XLAT 。

[lesswest]

WNDR4300 的没出来。。。还要自己动手

[lhbc]

@lesswest 我已经自己定制好了。
反正官方的都浪费 90M 空间，要完全利用 128M ROM 还是要定制。

这次的系统似乎大了点， 4M ROM 空间很蛋疼。

[lesswest]

@lhbc 分享个？

[iwfq]

之前的 IPK 还能用在 CC 上吗。。。

[lhbc]

@lesswest
https://www.stunnel.info/wp-content/uploads/openwrt-15.05-ar71xx-nand-wndr4300.tar.xz

以上固件创建自官方工具包，所有程序、代码均为官方，仅修改过分区表
官方工具包下载：
https://downloads.openwrt.org/chaos_calmer/15.05/ar71xx/nand/OpenWrt-ImageBuilder-15.05-ar71xx-nand.Linux-x86_64.tar.bz2

修改分区表
编辑文件 target/linux/ar71xx/image/Makefile
替换
wndr4300_mtdlayout=mtdparts=ar934x-nfc:256k (u-boot )ro,256k (u-boot-env )ro,256k (caldata ),512k (pot ),2048k (language ),512k (config ),3072k (traffic_meter ),2048k (kernel ),23552k (ubi ),25600k@0x6c0000 (firmware ),256k (caldata_backup ),-(reserved )
为
wndr4300_mtdlayout=mtdparts=ar934x-nfc:256k (u-boot )ro,256k (u-boot-env )ro,256k (caldata ),512k (pot ),2048k (language ),512k (config ),3072k (traffic_meter ),2048k (kernel ),121856k (ubi ),123904k@0x6c0000 (firmware ),256k (caldata_backup ),-(reserved )

创建镜像：
make image PROFILE=WNDR4300 PACKAGES="luci luci-theme-bootstrap uci dnsmasq-full wpad -wpad-mini -dnsmasq"
在官方 ROM 基础上，替换 dnsmasq 为 dnsmasq-full ，替换 wpad-mini 为 wpad

[lhbc]

@iwfq 应该可以
比如 ss ，我在 15.05 RC2 ， RC3 上使用良好
官方 ipk 肯定没问题

[iwfq]

感谢编译固件。请问你这个固件扩展名是 tar.xz ，要用什么方式刷呢？进 TFTP 可以刷吗？还是要在 openwrt 基础上直接升级？

[lhbc]

@iwfq 汗，看清楚才刷，免得变砖
这个是压缩包，解压里面有两个文件
对应官网上的两个
factory 是从网件官方固件改为 OpenWrt
sysupgrade 是从 OpenWrt 固件升级

[iwfq]

哈哈哈，谢谢谢谢~~~

[iwfq]

如果有 ZIP 或 RAR 的格式更好了哈~~~因为刚才试着 Winrar 解压不能。

[lhbc]

@iwfq WinRAR 直接解压 xz 格式
如果不能解压可能你需要升级 WinRAR

[debiansid]

X86-64 怎么改分区大小？

[lhbc]

@debiansid 找个 livecd Linux ，分区，再往硬盘写入系统就好了

[lesswest]

@lhbc 谢啦……懒癌晚期了我

[iwfq]

git 上面又把内核更新到 3.18.21 ，这是什么情况
https://dev.openwrt.org/log/branches/chaos_calmer/include?rev=46893
CC: kernel: update 3.18 to 3.18.21

可能要辛苦楼主再编译一个了。;D

[iwfq]

楼主，为什么你要加 luci-theme-bootstrap ，官方没带这个主题吗？

[lhbc]

@iwfq 带的，其实加不加都一样， luci 默认就是这个主题。

[lhbc]

@iwfq 不要看 trunk ，那个要很久才会合并到 release 里面

[ipiz]

@lhbc 感谢分享！官方版也已经放出来了。